Plastics Technology - Dedicated to improving Plastics Processing.
Issue link: http://pty.epubxp.com/i/802323
1. Find the appropriate tools and safety equipment. These include safety glasses, high-temperature gloves, arm protection, and nickel or molybdenum disulfide antisieze compound. Tools should be an appropriate wrench and a metal rod slightly smaller than the nozzle-tip orifice to clean out the nozzle. 2. Back the barrel/sled as far as possible, though with some machines there might be a better position for ease of access. 3. If electrical or thermocouple wires are in the way, turn the power off and take the time to permanently route along them to the non-operator side of the machine. It is safer and you will not get purged material on them, a common problem that causes hours of downtime to replace, at significant cost. It will save you time and anguish in the long run. 4. Purge the barrel if you are running a temperature-sensitive resin, such as PVC or POM (acetal). 5. Ensure the screw is forward with no spit- ting or drooling from the nozzle. Note: This is not a failsafe step—expect resin spitting and take all proper precautions. 6. Find the appropriately sized box-end wrench or socket. Use the six-point versions as they are safer because less likely to slip off. Ensure a good safe grip on the common 7/8-in. tip. 7. With the barrel up to temperature (heaters can be off if necessary) find the best position for the wrench to provide adequate leverage. On some machines, getting the wrench in place where you can get a decent grip and leverage it is next to impossible. (You wonder some- times if the machinery manufacturer ever has to do this.) A flexible or swivel end to the ratchet can be of help but tends to slip and is not as safe as a direct placement. 8. First, try to break the nozzle tip loose. Beware of the possibility of the wrench slipping and subsequent movement of your arms, hands, or torso banging against your surroundings. Normally you are cramped for space in this operation. 9. If you get it started, it should turn easily all the way out. If it turns but with effort, you have either a nozzle tip with bad threads or there is solidified carbon between the threads of the tip and the nozzle body. It will take significant effort to get the nozzle tip completely off. As for why, read steps 12-16. 10. If the nozzle is to be used again, I suggest cleaning it by using a dowel to push the plastic out from the front of the nozzle tip. (Remember to use appropriate heat-resistant gloves.) It is easier to clean while the plastic is molten. Look for carbon, a previous color, or material as a sign of dead space in the bull nose of the nozzle. 11. If you cannot break it loose, try tapping it with a hammer or add some heat. If you have to use a cheater bar, make sure the wrench is strong enough to take the load—and it had better be a six-point contact type. 12. Inspect the old nozzle's threads, nose, and seat for dings, burrs, or any non-uniformity; toss if not in good shape. If reusable, clean and store appropriately. Tossing it into a box or drawer is not acceptable. 13. Prepare the replacement nozzle tip by cleaning it and ensuring that it matches the radius of the sprue bushing of the mold and has the right size orifice—that is, slightly smaller if it is a cold runner, nearly the same size if a hot runner. Check that seat is clean and flat with no burrs or dings. Check that the nose is clean and not dinged. Double-check that the threads are symmetrical, clean, and lubed with a high-temperature and extreme-pressure anti-sieze compound. I like molybdenum disulfide. 14. Using protective gloves, start screwing in the replacement nozzle tip. If it does not start or turn easily, do not force it; you might get it on but it probably will not come off. Find out if the threads are stripped on the nozzle or nozzle body. 15. Screw the nozzle tip in until it seats but do not torque it tight. Turn it in until it gently seats then back off, wait 10 sec, and seat it again with low torque. Note whether it goes farther in. You are trying to make sure that the nozzle-tip seat is seating to the seat of the nozzle body with no plastic on either seat. Take time here to allow the nozzle tip to heat up and melt any plastic between the tip and nozzle-body seats. 16. With very low torque—say, less than 15 ft-lb, allow the nozzle tip to come up to temperature—perhaps 5-10 min. Then tighten it. If you tighten it as soon as you put it on, the nozzle tip will heat up, the threads will expand, and you can look forward to the nightmare in step nine. That should get you back into production. Remember, if the nozzle tip does not screw in or out easily once it is off the seat, there is something wrong. Forcing it will only make matters worse; you will be wasting more time, effort, and money over something that should not have happened to begin with. You do not want the nozzle body or the nozzle tip to change the temperature of the melt coming out of the end cap of the barrel. 30 APRIL 2017 Plastics Technology PTonline.com I N J E C T I O N M O L D I N G K now How ABOUT THE AUTHOR: John Bozzelli is the founder of Injection Molding Solutions (Scientific Molding) in Midland, Mich., a provider of training and consulting services to injection molders, including LIMS, and other special- ties. Contact john@scientificmolding.com; scientificmolding.com.